Ge Nx 448 Manual
Service If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at 1-800-448-0329. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. This product may be serviced only by the manufacturer or its authorized service agents. Changes or modifications not expressly approved by Thomson Inc. Could void the user ’s authority to operate this.
Thanks for the quick response George. I tried following the instructions. X8 9713 32# 49# Once I enter 49# I get 3 quick beeps, which would inticate an error. I checked the dip switches and all of mine are in the off position, an instruction manual i downloaded said that would be 35#, so I tried 35# instead of 32#. The same result. There is a sticker on the board that has a model number 60-732, I hope that helps.
- This package includes instructions for the following Caddx products: s. NetworX NX Series Receiver Modules—NX-408 & NX-408-I, NX-416 & NX-416-I, NX-448.
- Networx ™ nx-6 user manual. Nx-6 system keypad. This manual is furnished to help you understand your security.
There is also an instruction manual number 4661486. I can't see an NX number on the board. Thanks, Jason. Hi Jason, all wireless parts come from ITI which is also part of GE. For every different GE group panel manufacturer the receivers connect in different ways. For Caddx NX series panels the receiver must be designed for Caddx and has a 3 wire POS COM and DATA connection that connects on the keypad bus of the panel. Is your receiver connected this way?
Even the keyfob you have is the same as with other GE panels that integrate ITI wireless hardware but carries the NX prefix. The bad news is that from my search your ITI 60-732 seems only to be NX-8 compatible. The NX-4/6/8/8E compatible receiver is the 60-904. Both versions share the same document 466-1427 revision E August 1998 for the 732 and revision F July 2001 for the 904.
I think that the only difference between the two revisions is the NX panel compatibility list. As mentioned for the 60-732 it only states for NX-8 panel. I downloaded both documents from the GE site searching for 60-732. I already had the 60-904 document.
Both ITI versions apply to models NX-408 (8 zones), NX-416 (16 zones) and NX-448 (48 zones). There are also European (433 MHz versions) NX-4XX I.
Caddx Nx-448
Service If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at 1-800-448-0329.
I couldn't find your document 466-1486 so far. Please email the document to me to clear this up. Did you buy the receiver together with th keyfob? Was the receiver already installed with at least one wireless sensor learned on it?
Waiting for your feedback. The system was installed in the house when we had it built. They had a problem with one of the hardwired door sensors and installed a wireless sensor rather than fix the problem. I just purchased the key fob. The system has worked fine along with the wireless door sensor. The wireless receiver is a 3 wire POS COM and DATA and it is hooked to the keypad bus on the panel. I don't have document 466-1486, the number was on a sticker on the receiver.
I downloaded document 466-1427 revE thinking the install instructions would be similar. Thanks, Jason. Hi Jason, although the manual from 1998 states that the receiver is NX-8 compatible it doesn't mean it won't work with the NX-6. The NX-4/6 and 8E came later in the market. So I think mostly because of the 192 zone NX-8E they updated the firmware of the same receiver model. That's why many NX modules got the E at the end, like the NX-586 interface changed to NX-586E. If you get the 3 beeps negative acknowledge just after 49 # ( and NOT before) it means you get into the receivers program mode but a location 49 does not exist.
Nx-448
The newer firmware (the revision F manual I sent) has location 0 as learning location. So press. 8 9713 35 # (address is 35 = ALL 4 Dip Switches are OFF) 0 # and tell me the results.