Ih 6200 Press Drill Manual
1998 Case IH 5400 No-Till Seed Drill, Press Wheels, Grass Seed, Markers, Scrapers, Bushings, Coulter Castings, DP Springs, Seeds Tubes, Walkboard, 13'. We carry a wide variety of grain drill parts and air seeder parts for John Deere, Case-IH, Great Plains, Haybuster, Sunflower, Tye, United Farm Tools, and others.
However, drills are cost effective for establishment of close-spaced crops and are capable of placing seed at a uniform depth, provided depth-control or furrow-closing wheels are properly adjusted and maintained. Seed charts provided by drill manufacturers give a good starting point for obtaining the desired seeding rate, but they may not be very accurate.
Variables that can affect seeding rates include differences in seed size and shape among crop varieties (and sometimes seed lots), seed coatings or seed treatments, and seed density (bushel weight). From time to time, new species or mixtures of two or more species that are not listed on the drill seeding chart will be planted. For these reasons, a producer needs to know how to calibrate a drill. This fact sheet gives easy steps to calibrate your drill. Additionally, it is useful to check actual seeding rates by maintaining records of seed used and acres drilled over the years. Drill Calibration.
Determine the area 'seeded' when driving the calibration distance. Calibrate the drill for a driving distance of 200 feet. This is an arbitrary length, but it is long enough to capture variability in the field yet not too long to be impractical. Next, determine the width seeded by your drill.
In this example we will use a drill with a working width of 10 feet. Working width is calculated by multiplying the spacing between seed openers by the number of openers on the drill. The area seeded in our example will be 2,000 square feet (200 feet long by 10 feet wide). To calculate the fraction of an acre, divide 2,000 square feet by 43,560 square feet per acre to arrive at an area of 0.046 acre.
Determine the number of revolutions of the grain drill drive wheel when traveling the calibration distance. In the field use a measuring tape or other measuring device to measure a course that is 200 feet in length. Determine which wheel is responsible for driving the seeding mechanism on the drill. On some drills this is a special wheel that only runs the seed metering mechanism, while on other drills it is one of the wheels that supports the drill. You need to determine how many revolutions this wheel makes in the field in a 200-foot length. Make a mark or apply a piece of heavy tape to the wheel to enable you to easily count wheel revolutions while driving.
Drive 200 feet, which you previously marked out in the field, and count the number of revolutions made during the 200 feet. For increased accuracy, repeat this one or two times and use the average.
Set up the drill for calibration. Stationary calibration is accomplished by simulating drill operation. The seed delivery system of the drill is operated much in the same way as it is when being pulled across the field-by turning the drive wheel the number of turns determined in step 2 above. Stationary calibration is done by lifting the drive wheel above the soil surface so it can freely spin. Some type of hydraulic shop jack is often used to accomplish this.
Keep the drill securely attached to the tractor to maintain a level of safety when elevating the drive wheel and to operate the hydraulics on the drill. It is often necessary to lower the drill, permitting the drive mechanism to become engaged so that seeding rate calibration can be accomplished.
Using the rate chart supplied by the drill manufacturer (often found on the underside of the seed box lid), adjust the seed meter for the desired seeding rate of the species of interest. If your seed is not included on the chart, estimate a seeding rate by selecting a similar seed size. This will give you a first approximation. Ensure that enough seed has been added so that seed cups are full and seed metering fluted wheels or sponges are completely covered and will remain covered as seed is metered during the calibration process. Seed can be collected by one of two methods. The first involves the use of a large tarp that can be placed under all drill openers so that seed falling through the seed delivery tubes and disk openers can be collected from below the seed delivery mechanism and weighed. The alternate method involves removing the seed tubes from the disk opener assembly and placing them into several buckets or other containers used to catch and transfer all seed to one container for weighing.
At this time, the drive wheel can be turned (in the correct direction) until seed begins falling from all the openers. If some openers do not drop seed, ensure that seed tubes are not kinked or obstructed (straw, spider webs). Now you are set to start collecting seed for calibration. Ensure that the drive wheel has been turned to a convenient starting point (a mark on the drive wheel with chalk, marker, or tape is suggested) and that the tarp or buckets are clean. It is best to collect seed from all openers due to the small area that is represented for this calibration. Calibrate the drill. Turn the drive wheel the number of revolutions needed to represent 200 feet of travel, as determined during step 2 above.
Collect all the seed from the tarp or buckets and weigh the total. Use a balance with a gram scale and convert from grams to pounds by dividing by 454 grams per pound. Calibration is a trial-and-error process. The seed is collected from the simulated seeding of a fraction of an acre, weighed, and compared to the desired seeding rate.
If the rate is too low, the metering mechanism is adjusted to deliver more seed and the process is repeated. It is desirable to maintain a record of the seeding rates for each setting as one works toward the desired rate(s). Determining the seeding rate of the drill in this example is completed by dividing the total seed weight by the area 'drilled' (0.046 acres). For example, 2.3 pounds collected represents a seeding rate of 50 pounds per acre (2.3/0.046 = 50). If you want to check each opener for consistency, collect seed from individual seed tubes and record the weight of the seed from each tube.
Although the seed delivery system on a drill is not as precise as the seed-metering system on most corn planters, an amount collected from one opener that is 10 percent different from the average on all openers indicates a need for maintenance to the seed-metering mechanism. Considerations in Determining Seeding Rate and Seed Purchase A number of considerations are pertinent when determining seeding rates. A good source for seeding rate recommendations is your state's agricultural Extension office. Seeding rates are often recommended by seed suppliers for their specific species and varieties. These rates may be modified by planting date, soil type, whether drilling into tilled or no-tilled conditions, soil fertility levels, and other factors. Generally recommended rates are based on the desired plant population following emergence.
Seeding rates in pounds per acre will be determined with the knowledge of how many seeds are in one pound of seed. Once this information is known, the seeding rate should be modified to account for percent germination and the amount of non-seed that is indicated on the seed label. Hard seed is defined as seed that will not germinate as quickly as the other pure seed in the bag. Hard seed is common in legumes, but seed rates usually do not need to be adjusted for hard seed. Check with your seed supplier if you have seed with more than 5 percent hard seed. When selecting seed, always review the seed labels for purity and germination.
Pure live seed (PLS) is required by law to be stated on labels for all seed sold in Pennsylvania. PLS = purity x germination, or the percentage of the bulk seed weight that is viable and should germinate when planted. Keep in mind that PLS may vary among seed lots from the same supplier.
We describe all items to the best of our ability but all listings are for a guide only. THE BUYER IS RESPONSIBLE FOR INSPECTION AS TO CONDITION, YEAR AND MODEL before bidding. Bruce Schapansky Auctioneers and Seller disclaim all warranties expressed or implied about the merchantability of the items or their fitness for a particular purchase. All purchases become the responsibility of and shall remain at the risk of the purchaser immediately upon acceptance of their bid. All sales are final.
No purchase may be removed until paid in full including all applicable taxes. If for any reason the buyer fails to remove purchased item within specified time limit the auctioneer may have the item removed and resold or stored at buyers risk and expense.
Terms and conditions announced by Auctioneer Sale Day takes precedence over any written or verbal statements made prior to auction. All successful bidders must contact Bruce Schapansky Auctioneers Inc immediatly after the auction to arrange payment. Cash, Debit, Certified checks will be accepted. Visa/MasterCard will also be accepted with a fee of 3%. All items must be paid for within 24 hrs after the auction. BidSpotter will charge 3% up to a maximum of $600.00 per lot. Bruce Schapansky Auctioneers is providing internet bidding through the services of BidSpotter as a convenience to prospective purchasers.
The auction company or BidSpotter will not be held liable in any way shape or form for any disruptions or missed bids due to system lags or malfunction. We describe all items to the best of our ability but all listings are for a guide only. THE BUYER IS RESPONSIBLE FOR INSPECTION AS TO CONDITION, YEAR AND MODEL before bidding. Bruce Schapansky Auctioneers and Seller disclaim all warranties expressed or implied about the merchantability of the items or their fitness for a particular purchase.
Case Ih 6200 Press Drill Manual
All purchases become the responsibility of and shall remain at the risk of the purchaser immediately upon acceptance of their bid. All sales are final. No purchase may be removed until paid in full including all applicable taxes.
If for any reason the buyer fails to remove purchased item within specified time limit the auctioneer may have the item removed and resold or stored at buyers risk and expense. Terms and conditions announced by Auctioneer Sale Day takes precedence over any written or verbal statements made prior to auction. All successful bidders must contact Bruce Schapansky Auctioneers Inc immediatly after the auction to arrange payment. Cash, Debit, Certified checks will be accepted. Visa/MasterCard will also be accepted with a fee of 3%. All items must be paid for within 24 hrs after the auction. BidSpotter will charge 3% up to a maximum of $600.00 per lot.
Bench Press Drill
Bruce Schapansky Auctioneers is providing internet bidding through the services of BidSpotter as a convenience to prospective purchasers. The auction company or BidSpotter will not be held liable in any way shape or form for any disruptions or missed bids due to system lags or malfunction.